This mono audio amplifier board is driven by discrete power stage to provide high output power as 1000W per channel into a 2Ohm load in an ultra-compact size as 3.9’’ x 3.9’’ size. Based on our engineers’ years of experience and expertise accumulated in cooperating projects, this module gains a great balance between high quality and high performance, featuring high fidelity audio, low power consumption, flexible load characteristics, real strength for Hi-rel industry and ease of integration. All these features make this audio amplifier board applicable to subwoofer, car audio, Yacht and demanding industrial applications such as professional audio, underwater acoustics and alarm system. A DC30V-60V power supply is required.
High Audio Performance
Benefit from dedicated PCB layout design, careful components selection and engineers’ attentive debugging, this high power audio amplifier board produces powerful and clean audio with high audio performance, whose SNR reaches up to 96dB and THD+N performs well as 0.02% @ 4Ohm, 10W, 1kHz. Therefore, this module can provide quite powerful, warm and clean sound.
Supporting Both Single-ended Input and Differential Input
This high power audio amplifier supports single-ended input for easy integration into any projects. Besides that, it also supports differential input methods, which can vastly reduce the noise. Customers can choose to their requirements. The two input methods are optional, it is rather simple and convenient to switch with the provided toggle key (SW1) on the board.
High Level and Low Level Gain Switchable
To fully satisfy different requirements of various applications, this audio module offers two level gain for choice. High level gain is 37dB and low level gain is 33dB. Another toggle key is mounted on the board for the switch.
Flexible Load Characteristics and Wide Load Range
This audio amplifier module features flexible load characteristics with optimization in the frequency response. It has been tested in the lab with capacitive loads, inductive loads and resistive loads to make sure its stability and performance. Due to its low output impedance, this audio amplifier board supports wide load range from 1.5Ohm to 16Ohm without impact by the loudspeakers load characteristics.
Disclaimer: Extra attention needs to be paid for any operation with purely capacitive and inductive loads. It is suggested to send an inquiry email to us to confirm system compatibility with us before you use it to drive such loads.
High Reliability and Long Service Time
With a deep understanding of the importance of reliability in either DIY audio or industrial audio, we give no compromising on the protection circuit, components selection and lab testing of Brick series. With MOSFET integrated, the load capacity and robustness have been highly improved. Brick series sustained tough tests like HALT & HASS tests to ensure that it can work normally in the rough environment in industrial applications. Full protection circuit is equipped in the Brick series for safe operation and longer service time, including Reverse polarity protection, overcurrent protection, over temperature protection and so on.
Signal Level Sensor System
Signal level sensor system is equipped in this high power audio amplifier module for low power consumption. It will continuously monitor the input signal and there is a preset signal voltage threshold. When there is no signal (voltage is lower than the threshold) detected for a period of time, the amplifier board will enter into standby mode automatically, in which condition, it will consume lower power. The idle power when no signal detected is only 1.2W. When there is signal detected, it will go back to working mode immediately without miss of the audio.
Easy for Integration
A breakout board with terminals for input & control is attached in the package of the Brick series amplifier boards for simple connection. Interfaces on board include RCA, XLR and RJ128 terminals for easy integration of all the functions (Single-ended input, Differential input, Audio signal detection control, Shut down control and Single-ended output).
Please note that this audio amplifier is designed for audio applications. Please do not use it in non-audio applications. If you want amplifiers for non-audio applications, please contact with us. We will provide you with full set of audio solution with special optimization in specific requirements on frequency, protection settings or output voltage of different applications.
1pc Breakout board
1pc Cable for connection between the amplifier and the breakout board
1pc Speaker output cable
- Number Of Channel(s)1
- Output Power1000
- Size3.9 x 3.9 inches (99.06mm x 99.06mm)
- Heat DissipationHeat Sink & FAN
- Supported Parallel Bridge Tied Load Mode/
- inputSingle ended Line-in, Differential Line-in,
- Power Voltage36V-60V
- Output Power
- 1000W@2Ohm 56V DC THD+N 10%
- 750W@2Ohm 56V DC THD+N 1%
- Power and Clip Indicator
- Reverse Polarity Protection
- Signal Level Sensor System
- Flexible Connection and High Power Density
- Differential and Single-ended Optional
- High Level and Low Level Gain Adjustable
- Temperature Control Fan
- Full Protection
- Optimized Heatsink Design
- Weight: 650g/1.43 lbs (±10%)
- 3.90inch x 3.90inch PCB size
|Number of Channels||-||-||1||-||-|
|Minimum Load Impedance||-||-||2||-||Ω|
|Nominal Power Requirement||-||-||1200||-||W|
|Idle Power||Signal detected（Load 4 Ohm）||Fan on||-||15||-||W|
|No Signal detected||-||1.2||-||W|
|Standby Power||SD Connected to GND, Fan OFF||-||1||-||W|
|Switching Frequency||SD Floating@56V||-||700||-||kHz|
|Power Consumption||1/4 of max output power@4Ohm，56V||-||350||-||W|
|1/8 of max output power@4Ohm，56V||-||200||-|
|Control Standby||Pull down to GND current *||-||100||-||μA|
|Input Sensitivity||1000W@2Ohm，56V，1kHz||SE||Gain H||-||1.0||-||Vrms|
|Input Impedance||SE||Gain H||-||15||-||kΩ|
|Output Noise Level||A-weightingInput Connected to GND||SE||-||400||-||uV|
|DC Offset||@4Ohm， 56V||-||50||-||mV|
|Output monitor||Gain=350W @2Ohm，56V，1kHz||-||-39||-|