Hi, is it possible to use both Sigma Studio and Miumax at the same time? As in, first programming the ADAU1701 with SigmaStudio using your default program and then using Miumax to adjust gains? Or is it one or the other? Thanks!

Hi. SigmaStudio programming and Miumax control cannot be used the same time. When using Miumax control, DSP program will be covered by set program. When disconnecting with ICP5 and PC UI, the program you write will recover. Wish this could help you. Have a nice day~

Hello, I use ICP5 with JAB5. How can I transfer the DSP settings from ICP5 into JAB5. Currently, when I disconnect ICP5 from JAB5, I loose the DSP settings.

Hi, Bidjan. If you control JAB5 through SigmaStudio, you can writ the program into JAB5. If you control JAB5 through PC UI, the data will be saved in ICP5 rather than JAB5. So ICP5 needs to be connected to JAB5 if you want settings working. Wish this could help you. Have a nice day~

hello, i need help. my jab5 with ICP5, when I turn it off and on it makes a popping sound, without music playing, the speakers jump. without ICP5 this does not happen. does that happen? and what to do to resolve?

Hello, Venan. Please operate with standby control function (J11) on JAB5, which is equipped with pop noise removal circuit. Wish this could help you. Have a nice day~

Hello, i have many problems with the new Miumax App and the ICP5. Maybe another have the same problems. When i start my JAB5 Wondom TDA4100 make the Speakers a loud crackling sound. And when i make louder the JAB5 limit the subwoofer and the sound drops. I have the 2.1 config. But with the original factory setting and the 4 potis all works perfect. Thanks for help.

Hi, Andi. After ICP5 firmware upgrade completion, please follow the steps to connect ICP5 with JAB5. 1. Make sure SW2 of ICP5 is set at 2-REMOTE, disconnect ICP5 with PC, 2. Connect ICP5 with JAB5, 3. Connect ICP5 to your PC for control then. If there is noise, you can press the SW3 button on ICP5. If there is still problem, please send some videos to us so that we can pinpoint the problem and solve it. Wish this could help you. Have a nice day~

I bought the ICP5. It seems that Windows 11 x64 USBi driver is missing. How do I connect?

Hi, Anthony. Please kindly try with the following USB driver to see if it works. http://store.sure-electronics.com/images/documents/64bit_USB_Driver_CH341SER.zip Wish this could help you. Have a nice day~

Does this work with JAB5 yet?

Hi, Elmer. Thank you for your kind wait. Here is the PC UI contorl for JAB5. Step 1, Download the Miumax for JAB5, and install it. https://store.sure-electronics.com/images/documents/Miumax%20for%20JAB5-1.0.3.zip Step 2, Install the USB driver. If you have installed it before, you can skip this step. If you don’t install it before, here is the link. https://store.sure-electronics.com/images/documents/Win10%20Driver.zip Step 3, Set SW1 on ICP5 at ② (REMOTE). Step 4, Update the firmware of ICP5. Press the SW3 on ICP5 and hold on, meanwhile connect ICP5 to your PC with a USB Type-C cable. Then release SW3, and you can see the “RUN” LED on ICP5 blink, that means ICP5 enters Bootloader Mode. In this condition, it will show “Firmware Upgrade Mode” on the top left corner of the UI. Click “Update” icon on the Miumax for JAB5 and wait for upgrade completion. You can refer to “Online Upgrade” section of ICP5 User Guide. https://store.sure-electronics.com/images/documents/WONDOM%20ICP5%20User%20Guide%20Programmer%20for%20Programming,%20APP%20&%20PC%20UI%20Control_V1.02.pdf Step 5, Connect ICP5 with JAB5. It will show “JAB5 is connected” on the top left corner of the UI. If it doesn't show this prompt, please re-start the Miumax for JAB5. If there is no sound after connection, please turn up the input and output volume and reset the filter settings of each channel on Miumax. Then, you can adjust the parameters to your requirements. Step 6, If you want to save your configurations to your ICP5 and run it without connection to PC, please click “Save all parameters to ICP5” icon. After the writing is done, re-power your JAB5. Wish this could help you. Have a nice day~

Hi, Is the App Control ready for the ICP5 yet, as it was suppose to be released at the end of July 2022, also any news on the PC UI ? Thanks Rupert

Hi, Rupert. Thank you for your kind wait. The PC UI for JAB5 has been released on the detailed product page of JAB5 and ICP5. Wish this could help you. Have a nice day~

Hi, When programming an AMP2 module, do I need to have this ICP5 module connected at all times? Or can I just run my program and disconnect the ICP5? I am planning on using a single ICP5 module to program 3 AMP2 modules for a 5.1 setup, so just programming each board once and disconnecting the ICP5 afterward.

Hi, willie. If you want the program to be run offline, you need to write the written program into your DSP. After than, you can disconnect ICP5 with APM2. Wish this could help you. Have a nice day~

When will there be a PC UI support for JAB-5?

Hello, Ian. Thank you for your patient waiting. Our R&D department are speeding up the debugging and test of PC UI of JAB5. We will release it soon. Have a nice day~

Still not ready yet PC UI and phone application for JAB5? I know is a estimated time, but this is too long :). I need DSP settings my JAB5 amplifier...

Hello, Ladislav. Thank you for your patient waiting. Our R&D department are speeding up the debugging and test of PC UI of JAB5. We will release it soon. Have a nice day~

I bought this to connect to a jab5. There is a 4 pin connector on this board but none on the jab5. How do i connect this this to the jab5?

Hi, Brian. The 4pin PH connector on ICP5 is used to connect to JAB2v2. You can connect ICP5 to JAB5 through the 6pin PH connector (J1) on ICP5. Wish this could help you. Have a nice day~

Is it possible to control a jab2v2 using the PC miumax software via Bluetooth using the ICP5?

Hi, andrew. Thank you for your interest in our products. The control communication between the PC UI and ICP5 is achieved by UART protocol. Therefore, ICP5 must be connected to PC via USB cable if you want PC UI control of JAB2v2. Wish this could help you. Have a nice day~

Will this work on a JAB2v2 that has been connected to a JAB3 that is used for a sub-woofer?

Hi, andrew. Thank you for your interest in our products. Yes. ICP5 can work with a JAB2v2 taht has been connected to a JAB3. Wish this could help you. Have a nice day~

I'm confused. Does this work with JAB4 or not? Thanks

Hi, Siavash. Yes. JAB4 can work with ICP5. But for now, it only supports programming through SigmaStudio after connection as PC UI and APP haven't released yet. Wish this could help you. Have a nice day~

Hey, hey can someone help me. I want to do the update like in the User Manuel shown. I have connected the ICP5 while pressing the button with my pc. SW1 is set to 2. The Led (RUN) is fleshing yellow. I clicked the button Upgrade on the Miumax_JAB2 Software and it says "Device Searching..." but nothing happens. (SW4 is set to 1) Thanks!

Hello, Fynn. Please install this USB driver and try again. https://store.sure-electronics.com/images/documents/Win10%20Driver.zip If there is still problem, please feel free to contact us with store@sure-elecronics.com. It'd be better if there is any pictures or videos attached for our check. Wish this could help you. Have a nice day~

Hello, is this product (ICP5) currently fully functional for PC control via UART with the existing APM2 device? --> https://store.sure-electronics.com/product/658 Thanks.

Hello, Steven. 1. SigmaStduio Programming All WONODM products integrated with ADAU1701 DSP can support programming through SigmaStudio after connection with ICP5. Therefore, APM2 supports programming after connection with ICP5. 2. PC UI Control For now, there is only PC UI for JAB2v2. We are working hardly to release PC UI in succession for other products. 3. APP Control There is no APP available now. We will develop APP after all the PC UI are released. Wish this could help you. Have a great day~