Description
This power supply is ideally suited for use with amplifier projects. The regulated 5 VDC, 3A design is capable of delivering 15watts of output. Overload, over voltage, and over temperature protection is built-in, shutting down the power supply to prevent damage and then restoring power upon recovery.
- TypeAD/DC Power
- StyleEnclosed
- Output ChannelSingle
- Universal AC input/Full range
- Protections: Short circuit / Overload / Over voltage/Over temperature
- Cooling by free air convection
- 100% full load burn-in-test
MODEL | NES-15-5 | |
OUTPUT | DC VOLTAGE | 5V |
RATED CURRENT | 3A | |
CURRENT RANGE | 0 ~ 3A | |
RATED POWER | 15W | |
RIPPLE & NOISE(max.) (Note.2) | 150mVp-p | |
VOLTAGE ADJ. RANGE | 4.75 ~ 5.5V | |
VOLTAGE TOLERANCE (Note.3) | ±2.0% | |
LINE REGULATION(Note.4) | ±1.5% | |
LOAD REGULATION (Note.5) | ±1.5% | |
SETUP, RISE TIME | 1000ms, 30ms/230VAC 1000ms, 30ms/115VAC at full load | |
HOLD UP TIME(Typ.) | 100ms/230VAC 20ms/115VAC at full load | |
INPUT | VOLTAGE RANGE | 85 ~ 264VAC 120 ~ 370VDC |
FREQUENCY RANGE | 47 ~ 63Hz | |
EFFICIENCY(Typ.) | 79% | |
AC CURRENT(Typ.) | 0.35A/115VAC 0.25A/230VAC | |
INRUSH CURRENT(Typ.) | COLD START 45A | |
LEAKAGE CURRENT | <2mA/240VAC | |
PROTECTION | OVERLOAD | Above 105% rated output power |
Protection type: Hiccup mode, recovers automatically after fault condition is removed | ||
OVER VOLTAGE | 5.75 ~ 6.75V | |
Protection type: Shut off | ||
OVER TEMPERATURE | U1 Tj 140°C typically(U1) detect on main control IC | |
Protection type: Shut down O/P voltage, recovers automatically after temperature goes down | ||
ENVIRONMENT | WORKING TEMP. | -20 ~ +60°C (Refer to derating curve) |
WORKING HUMIDITY | 20 ~ 90% RH non-condensing | |
STORAGE TEMP., HUMIDITY | -40 ~ +85°C, 10 ~ 95%RH | |
TEMP. COEFFICIENT | ±0.03%/°C (0 ~ 45°C) | |
VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | |
SAFETY&EMC(Note.7) | SAFETY STANDARDS | UL60950-1, CB(IEC60950-1),CCC GB4943.1:2001 approved |
WITHSTAND VOLTAGE | I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC | |
ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C / 70% RH | |
EMC EMISSION | Compliance to EN55022(CIRPS22) Class B, EN61000-3-2,-3 | |
EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61000-6-1, light industry level, criteria A | |
NOTE | 1. All parameters NOT specially mentioned are measured at 230VAC input,rated load and 25°C of ambient temperature.2. Ripple & noise are measured at 20MHz of bandwidth by using a 12’’ twisted pair-wire terminated with a 0.1μf & 47μf parallel capacitor.3. Tolerance: includes set up tolerance, line regulation and load regulation.4. Line regulation is measured from low line to high line at rated load.5. Load regulation is measured from 0% to 100% rated load.6. For the request of GB4943.1, the power supply is only suitable for use in the altitude 2000m below and the non tropical climate condition.7. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC test, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) |