Sign up

Home /
Audio Amplifier Board /

2 x 50 Watt Class D Audio Amplifier Board w Bluetooth Ver4.0 - JAB2[640]

★★★★★(751 recommends)



Add To Cart
Buy Now


Buy 27 for $37.521 each and save 1%

Buy 53 for $37.142 each and save 2%

Buy 80 for $36.763 each and save 3%


1 x 60 Watt Class D Audio Amplifier Board w DSP - JAB3-160



1 x 100 Watt Class D Audio Amplifier Board w DSP - JAB3-1100



Bluetooth Pairing Name Programming (store@sure-electronics.com)



L-style Aluminum Bracket (JAB accessories)



Cables Package for JAB (JAB accessories)



3S18650 Lithium Battery Balance and Protection Extension Board (JAB accessories)



Interface Extension Board with USB Charge Only (JAB accessories)



2 x 50 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-250 (for Gaming Kiosks)



2 x 30 Watt Class D Audio Amplifier Board with Audio DSP - JAB3-230 (for Gaming Kiosks)




As a member of JAB(Audio Amplifier Boards designed for Jukecase) series, JAB2 offers the wireless solutions with Bluetooth module integrated and can be powered by lithium batteries directly. It is a stereo Class D audio amplifier board capable of delivering 30W @ 4 Ohm with a Texas Instruments TPA3116 chip to achieve high efficiency. Each channel is capable of delivering outputting nominal power simultaneously and continuously. The module dissipates only 0.72W with no signal when in ON mode (around 0.07W when in stand-by mode). Excellent heat dissipation eliminates the requirement of an extra heatsink and increases its reliability. Over current protection and over temperature protection are included to extend the longevity of the amplifier board. All these features make it a good choice for portable Bluetooth speakers.

Video for introduction of JAB2: video link

Video for introduction of Bluetooth control: video link

Video for connection with JAB3: video link

  • StyleBoards
  • Number Of Channel(s)2
  • Output Power50
  • Size3.6 x 2.7 inches (91.44mm x 68.58mm)
  • ChipsetTPA31xx
  • Heat DissipationHeat Sink
  • Supported Parallel Bridge Tied Load ModeYES
  • inputBluetooth, Single ended Line-in,
  • Power Voltage10V-24V
  • 3.6 x 2.7 Inches PCB Size
  • Bluetooth V4.0 APT-X +EDR, A2DP
  • Power Management Circuit
  • 3.5mm AUX Port
  • Volume Control Port (Potentiometer)
  • Power Switch Port
  • LED Status Indicators (Power, Battery Charging, Bluetooth)
  • Disconnection from Lithium Battery
  • Higher Output Power with Power Adapter
  • PBTL Configurable
  • Extension Board Supported (Coming soon)
Specifications typical @ +20℃, Powered by 19V DC, unless otherwise noted. Specifications subject to change without notice.
Parameter Conditions Min. Typ.  Max. Units
Power Supply Range - 12 19 24 VDC
Idle Power/Current SD short to GND, BT Disconnected - 37 50 mA
BT Connected - 42 55 mA
Standby Power/Current SD short to GND, only when low power module available - 2.9 5 mA
Battery Undervoltage Protection* - - 10.4 10.5 V
Constant Charging Voltage - - 12.3 12.7 V
Charge Current - - 0.5 1 A
Specifications typical @ +20℃,Powered by 19V DC, unless otherwise noted. Specifications subject to change without notice.
Parameter Conditions Min. Typ. Max. Units
Gain -     18 26 36 dB
Output Power19V @ 4Ω 2 x 50    W
THD @ 4Ω,10W, 1kHz - 0.02 - %
Output Noise Level A-weighting,Input Connected to GND       - 185 - µV
SNR 10W @ 4Ω, THD+N=1% - 92 - dB




21 Oct 2019

if i wish to add a sub and a tweeter, would i need a crossover? and which would you recommend?

Hi, Lasse. Thank you for your interest in our products. If you want to add a sub and a tweeter, a crossover is required. We recommend you the JAB3 - 250 (2 X 50 WATT CLASS D AUDIO AMPLIFIER BOARD WITH AUDIO DSP), which can be connected with JAB2 - 250 to build an audio 4.0 system integrated with Bluetooth and DSP. Wish this could help you.


11 Sep 2019

Hello. Could I use PS-BC12113 to power this board (AA-JA32171)? As i understand, this board needs voltage higher than 12 volts

Hi, thank you for your interest in our products. The power supply range of AA-JA32171 is DC12V-24V. The voltage of PS-BC121113 (5S 26650 Lithium Battery Charging, Balance and Protection Board-BCPB4) can reach DC21V when fully charged. So it can be used to power the JAB2-250. In addition, there are multiple discharging ports on PS-BC12113 so it can be used to power the audio 2.1 system built with WONDOM JAB2 and JAB3. Wish this could help you.


23 May 2019

Is it already the newer version with external antenna?

Hi, Gábor. Thank you for your interest in our products. Yes, the external antenna together with 1pc power cable and 1pc speaker cable is in the package of JAB2-250. Please feel free to contact us if there is any problem.


26 Mar 2019

If we want to use a third party potentiometer what resistance should it be

Hi, Surya. The resistance should be 1k-10k, which depends on the noise floor. We recommend 1k. Wish it could help you.


28 Feb 2019

Does this come with volume pot and power cable? Can the Bluetooth name be programmed? Thanks Marc

Hi, Marc. The power cable is sent with the JAB2 package and the volume potentiometer is in the Functional Cables Package, which you can buy in the following link: http://store.sure-electronics.com/product/AA-JA11114 or http://store.sure-electronics.com/product/AA-JA11116. If you want to rename the Bluetooth, please contact us with store@sure-electronics.com. This new online shop is under construction now and it will be improved soon. Thank you for your support and sorry for the inconvenience brought to you.

Copyright 2020 @ Sure Electronics Co., Ltd.